• Skip to primary navigation
  • Skip to main content
Just Lugger Joinery

Just Lugger Joinery

  • Home
  • Products
    • Joinery
    • Spars
    • Accessories
  • How to Do It
  • Client Stories
  • Workshop Courses
  • Phil’s Workshop Blog
  • Ordering

Flooring for ‘Damson Drifter’ hull number 5

A new project arrived at NP22, Simon has travelled down from North London with the complete flooring out of his Drascombe Drifter. It’s a 1970’s built hull with its original flooring, all in a very poor state and the material used was not particularly good to start with.

UPDATE: Check out Simons reaction at the bottom of this post

Simon has followed our work at JLJ over the past year or so. In particular the work on Robin’s Drascombe Drifter 22, the joiner supplied to Henry in Bahrain for his Longboat and the keel band and flooring shipped out to Nice in the south of France for Tom’s Mk 3 Lugger just to mention a few of our satisfied clients. These have compelled him to make the trip down to Wales with his flooring, in the knowledge that this work can be undertaken. Brought down on 18 February and Simon visited again on 7 March to collect the finished new flooring.

Apart from the sorry state that the flooring was in Simon had a major issue with the larger of the floor lift up access sections.

He has a small inboard engine under this flooring grid and there is pipe work that runs high near to the underside of the floor that was infringing on he face mounted floor straps.

To get over this the carpenter had just hacked out slots in these straps to allow these pipes to pass, resulting in the floor was not secured as a stable unit, not at all a very clever piece of work.

This strapping arrangement can be seen in the pics provided and it’s evident that neither the material or the quality of the manufacture is good.

So it was now time to have a re think on how to make new floor sections that didn’t interfere with the pipe work and produce all new flooring out of a far higher quality of material.

You will have read from my past blogs and joinery details that I only use a softwood that has a joinery grade, this being a Finnish, Upper Gulf Unsorted Redwood, what you see in builders yards is a poor quality ‘Whitewood’.

The proposal I made to Simon was to dispense with these surface mounted straps and to machine slots in the underside of the grids so stretcher rails can be fitted, their only purpose is to keep the grid together, these being made out of Ash and after each slat had been individually spray varnished finish they were glued and screwed together.

A time consuming process, however to get full protection it is the only method that one can guarantee an overall surface penetration of spray varnish.

From the before and after pics you can identify the care and accuracy of replicating not only the overall dimensions but the copying of the underside profiling and adding additional edge chamfering to take away sharp edges which will not hold a varnish finish

Yet another successful project and it’s now time to move on to the next workshop project.

A boom for a Lugger!!! What a suggestion I heard from devoted Lugger owners!

Nic who is based on the East coast wants to get a better sailing performance in the restricted waters of East Anglia, it’s not new to me I had a boom on my Mk3 Lugger JOJO out in the South Ionian Sea, pictured left, and it did indeed make a big difference.

So with little more to do work is now underway this week, 8 March on the making of the 2.9m boom out of Douglas Fir, a great material for making spars!!

So keep posted to the website for updates!!!! Also check out our Standard Flooring below or get in contact for more bespoke work as seen in this post.

Flooring
Get in Contact

UPDATE!!!!! Simons Reaction

“I am really pleased with the look and the fit.

I had to clean the cockpit floor first and laid them in. Both outer boards with the curved side, also fit in their secondary place as cockpit bunks. This is just great news and I may ask you for an additional port and starboard curved board in the future.

The engine cover with fiddles also fits well, but I have to do more work on the cabin wood work, surrounding the engine.

I now have to decide if I send the boat for it’s engine service to the boatyard with the new floor boards – as I don’t want some”heavy footed” engineer messing them up, but I guess they will survive even that….!” Simon

Copyright © 2026 Dragon Design · Contact Details · Terms & Conditions · Materials · About Us